Dimensions and conditional planning weights for HessTrees boxed specimens and field-dug root balls. The original reference has been recreated with corrected arithmetic, transparent soil-density assumptions, and a working estimator. These are not measured weights or engineered lift limits.
72″ – 144″ box range8′ – 16′ root ball range108″ / 120″ and up hero materialWide-load oversize to 16′
⚖️
How to use these weights: Every figure is a conditional planning estimate, not a scale ticket. Actual weight depends on measured soil volume and wet density, the particular tree, box and handling gear. Confirm by scale or load cell before a critical lift, structural placement or freight commitment. Have a qualified lift planner and structural engineer review the actual conditions. No value on this page establishes safe lifting capacity.
The box — tapered, not square
Shown empty, as built: rough-sawn plank courses, vertical steel strapping with a top band, heavy corner battens, a thick timber rim, and skid runners underneath. Every HessTrees box is built with a fixed 18-inch taper, top to bottom — the base measures 18″ narrower than the top on every box size (base = top − 18″). The taper lets the root ball release cleanly and keeps the box stable on forks and slings.
Fig. 1
Top — example shown96″ × 96″
Base (18″ taper)78″ × 78″
Depth54″
Illustrative weight*25,900 lb*
The root ball — side profile, flat on the ground
Shown in a straight side profile, resting flat on the ground with the trunk up — how a field-dug ball sits at grade. The wrap is burlap, wire- and rope-laced. Diameter is the governing spec; depth is held to 36″–42″ even at the largest sizes.
Fig. 2
Diameter — example shown14′ (radius 7′)
Depth42″ (model)
WrapBurlap, wire + rope laced
Illustrative weight*37,700 lb soil only*
* Diagrams are not to scale. Box example: 237.375 cu ft × 100 pcf + 2,200 lb unverified tree/box allowance. Root-ball example: 14′ diameter × 42″ depth at 70% cylinder × 100 pcf, soil only. Geometry and density must be measured for the actual specimen.
01 — Boxed Specimens
Box sizes & estimated weights
All listed boxes use the original 18-inch top-to-base taper: base = top − 18″. Volume is a square frustum, not a straight-sided prism. These nominal dimensions are assumed to be inside soil dimensions; measure the actual fill before use. The illustrated total uses 100 lb/cu ft as-handled wet density plus the original, unverified tree-and-box allowance. A soil type alone does not establish density.
72″ box
Starter specimen
Top72″ × 72″
Depth42″
Base (taper)54″ × 54″
Soil volume97.1 cu ft · 3.60 yd³
Illustrative total @ 100 pcf10,900 lb≈5.5 US tons · includes 1,200 lb allowance*
84″ box
Standard
Top84″ × 84″
Depth42″
Base (taper)66″ × 66″
Soil volume137.4 cu ft · 5.09 yd³
Illustrative total @ 100 pcf15,200 lb≈7.6 US tons · includes 1,500 lb allowance*
96″ box
Large specimen
Top96″ × 96″
Depth54″
Base (taper)78″ × 78″
Soil volume237.4 cu ft · 8.79 yd³
Illustrative total @ 100 pcf25,900 lb≈13.0 US tons · includes 2,200 lb allowance*
108″ box
Hero material
Top108″ × 108″
Depth54″
Base (taper)90″ × 90″
Soil volume307.1 cu ft · 11.38 yd³
Illustrative total @ 100 pcf33,300 lb≈16.7 US tons · includes 2,600 lb allowance*
120″ box
Hero material
Top120″ × 120″
Depth54″
Base (taper)102″ × 102″
Soil volume385.9 cu ft · 14.29 yd³
Illustrative total @ 100 pcf41,600 lb≈20.8 US tons · includes 3,000 lb allowance*
132″ box
Oversize
Top132″ × 132″
Depth54″
Base (taper)114″ × 114″
Soil volume473.6 cu ft · 17.54 yd³
Illustrative total @ 100 pcf50,800 lb≈25.4 US tons · includes 3,400 lb allowance*
144″ box
Maximum box
Top144″ × 144″
Depth54″
Base (taper)126″ × 126″
Soil volume570.4 cu ft · 21.12 yd³
Illustrative total @ 100 pcf60,800 lb≈30.4 US tons · includes 3,800 lb allowance*
Hero material is a class, not just a number
Hero material is the 108″ / 120″ class and up — and it is not necessarily the size of the box alone. Where a tree runs larger than any box spec, HessTrees supplies it as an oversize root ball (below) up to 14′ and 16′, transported as a wide load. Projects rarely need one hero tree — a dozen or more for a single job is typical.
Density is a measurement, not a label
Wet soil weight changes with moisture, compaction and material. A universal “12–18% wetter” rule is not supported. Use the supplier’s tested as-handled density; for structural design use the project engineer’s required saturated condition. Original figures remain in the review record below.
Box
Top × Depth
Base (taper)
Soil volume
Total @ 100 pcf*
72″
72″ × 72″ × 42″
54″ × 54″
97.125 cu ft
10,900 lb
84″
84″ × 84″ × 42″
66″ × 66″
137.375 cu ft
15,200 lb
96″
96″ × 96″ × 54″
78″ × 78″
237.375 cu ft
25,900 lb
108″
108″ × 108″ × 54″
90″ × 90″
307.125 cu ft
33,300 lb
120″
120″ × 120″ × 54″
102″ × 102″
385.875 cu ft
41,600 lb
132″
132″ × 132″ × 54″
114″ × 114″
473.625 cu ft
50,800 lb
144″
144″ × 144″ × 54″
126″ × 126″
570.375 cu ft
60,800 lb
* Conditional examples, not verified weight ranges. The example uses an assumed as-handled soil density of 100 lb/cu ft. Totals include the original unverified tree + box allowances (1,200–3,800 lb), exclude rigging, and round to the nearest 100 lb. Actual measured density and allowances are required. Click a size card to edit the assumptions.
02 — Field-Dug Root Balls
Round balls — diameter & weight
For a round ball the governing dimension is diameter (radius × 2). Depth stays in a narrow band — 36″ to 42″ — even as diameter climbs, because a field ball is a broad, shallow root plate, not a sphere. Balls are dug, wrapped, and held to root in / harden off before shipping.
Ball diameter
Radius
Depth
Modeled volume*
SOIL ONLY @ 100 pcf*
Transport
8′
4′
36″
105.6 cu ft
10,600 lb + tree, wrap & handling gear
Standard flatbed
10′
5′
36″–39″
164.9–178.7 cu ft
16,500–17,900 lb + tree, wrap & handling gear
Wide load — flatbed, permit req.
12′
6′
39″–42″
257.3–277.1 cu ft
25,700–27,700 lb + tree, wrap & handling gear
Wide load — lowboy / step-deck
13′
6′ 6″
39″–42″
302.0–325.2 cu ft
30,200–32,500 lb + tree, wrap & handling gear
Wide load — lowboy
14′
7′
42″
377.1 cu ft
37,700 lb + tree, wrap & handling gear
Wide load
15′
7′ 6″
42″
433.0 cu ft
43,300 lb + tree, wrap & handling gear
Wide load — oversize
16′
8′
42″
492.6 cu ft
49,300 lb + tree, wrap & handling gear
Wide load — oversize
* Uses the original 70% of a cylinder assumption, not a verified root-ball standard, and 100 lb/cu ft assumed wet density. Variable-depth rows now show both ends of the depth range. These are soil-only masses, not delivered-tree weights. A full cylinder of the same dimensions holds about 43% more soil. Measure actual geometry; boxing a ball does not automatically give it a standard box’s weight.
Planning tool · explicit assumptions
Estimate from geometry & density
Choose a specimen, then replace the assumptions with measured dimensions and as-handled wet density. Moisture is already included in wet density; it is not multiplied a second time.
Original box allowance is unverified. For a root plate, add the actual tree and wrapping weight.
Zero means not included, not that no rigging is needed.
Conditional planning total25,900 lb
≈13.0 US short tons
Modeled soil volume
Soil component
Tree + container / wrap
Handling / rigging
Not a lift plan. Confirm actual weights and have a qualified person check the crane’s load chart at the actual radius and configuration. For elevated planting, the structural engineer must also check the saturated condition, load distribution, planter and other permanent loads.
03 — Date Palms
Palm weight starts with brown trunk
Date palms — Medjool, Zahidi, and Deglet Noor, now orderable at HessTrees.com — are estimated on a different basis from boxed broadleaf specimens. HessTrees' field rule is about 100 lb of trunk weight for every foot of brown trunk. The exception is male Medjool, at 150 lb per brown-trunk foot. The root ball weight is additional in both cases.
Supplier field rules retained: the 100 and 150 lb per brown-trunk-foot figures are HessTrees’ original estimates, not independently validated weights. They exclude the root ball and must not substitute for actual weighing.
The 100-lb field rule — and the male Medjool exception
For Medjool, Zahidi, and Deglet Noor, trunk weight is estimated at ≈ 100 lb per foot of brown trunk — the clear, woody trunk measured below the living crown.
Male Medjool runs heavier: ≈ 150 lb per foot of brown trunk.
Both figures are planning estimates, not scale weights: actual trunk weight varies with trunk diameter, moisture, and how the palm was grown and prepared. Brown-trunk height is specified and measured per palm at order.
Brown-trunk weight tables
Medjool, Zahidi & Deglet Noor — ≈ 100 lb / ft
Brown trunk
Est. trunk weight
10 ft
≈ 1,000 lb
15 ft
≈ 1,500 lb
20 ft
≈ 2,000 lb
25 ft
≈ 2,500 lb
30 ft
≈ 3,000 lb
Trunk weight only, at ≈ 100 lb per brown-trunk foot — planning estimates.
Male Medjool — ≈ 150 lb / ft
Brown trunk
Est. trunk weight
10 ft
≈ 1,500 lb
20 ft
≈ 3,000 lb
30 ft
≈ 4,500 lb
Trunk weight only, at ≈ 150 lb per brown-trunk foot — planning estimates.
Palm root balls — 36″ to 54″, field-dug
The tables above are trunk weight only. The root ball is additional. Palm root balls run 36″ to 54″ — that is the standard range, and no root ball smaller than 36″ is offered. If a job requires a specific root ball size outside that standard range, additional fees apply.
Palms are not boxed. The balls are cut by hand and with mechanized equipment and pulled directly from the field. These are field-grown palms from working farms — the same ground the fruit is harvested from — not container-grown in a controlled environment. Dimensions are therefore field-cut, not exact: expect the ball to come in close to, not precisely on, the specified size.
A crane lifts a boxed specimen tree onto a flatbed trailer for transport.
04 — International Palm Shipping
Root wash & climate-controlled containers
Exporting palms is an agricultural compliance process as much as a freight process. HessTrees prepares international palm orders to the phytosanitary requirements of the destination country before any palm is loaded.
Import requirements, permits, phytosanitary certificates and transit conditions must be confirmed with the destination authority for each shipment.
Loading washed palms into a climate-controlled container for overseas shipment. Root balls are washed free of native soil and inspected before loading, as required by destination-country agricultural authorities.Palms loaded inside the shipping container.
Palms secured for transport.Boxed root system on a transport trailer.Specimen tree secured for the haul.
Root wash — required before export
International palm shipments generally require a root wash: all native soil is washed from the root balls before export. The requirement is imposed by most destination countries' agricultural departments and plant-health authorities, because native field soil can carry pests, pathogens, and weed seed that importing countries will not admit.
The wash is completed — and any inspection required by the destination authority is carried out — before loading. A palm that has not been washed and cleared does not go into the container.
Loading & transit
Once washed and cleared, the palms are loaded into climate-controlled shipping containers for the ocean voyage. Climate control protects bare-rooted, washed palms from the heat, cold, and drying they would otherwise face in transit, so they arrive in suitable condition for planting.
Sequence: dig and prepare the ball, wash all native soil from the root ball, complete any required inspection, then load.
Experience: HessTrees has shipped 500+ palms internationally, including orders to the Dubai, UAE, and Saipan.
Plan for it: root washing, inspection, and container booking are lead-time items. Specify the destination when requesting a quote so we can schedule export preparation.
05 — Elevated & Weight-Sensitive Planting
Reduced root balls & podium-depth boxes
On a podium, a parking structure or a hotel terrace, both the supporting structure and the crane’s capacity at the actual lift configuration constrain the placement. A reduced root ball, a box sized to the permitted depth, and time to regenerate roots are part of the project-specific plan.
Supplier practices below are retained from the original, including podium depths, 90-day rerooting and the October–February planning window. They are not universal horticultural standards; confirm the species, climate and project schedule with the nursery and project arborist.
How the weight comes down
Soil is the bulk of the illustrated weight: with the stated 96″ dimensions, assumed 100 pcf wet density and unverified 2,200 lb tree/box allowance, it is about 91.5% of the modeled total. That fraction is conditional, not a measured species-wide range. Reducing soil volume changes weight directly.
Reduced root ball — the ball is cut smaller than the standard spec for the tree's class. Fewer cubic feet of soil is the most direct weight saving there is, and it is how HessTrees brings a podium tree down to a structural allowance.
Podium box depth — typically 24″ to 30″ — podium boxes do not use the standard box depths on this page (42″ on the 72″/84″ boxes, 54″ from 96″ up). A podium planting is sized to the box the structure allows, and those boxes typically run 24 to 30 inches deep. Tell HessTrees the box size and the depth the structure permits — depth is a governing dimension for podium work, not a default.
Specialized boxing — box construction and root-ball trim sized to a weight target, not just a nominal box class.
Load documentation — per-tree estimated weights supplied with the quote so the structural engineer can check the placement before the tree ships.
The planting soil that goes into a structure is specified by the project team — the architect and engineer — not by HessTrees.
Bring the structural allowance — and the box depth the structure allows — to the first conversation. Weight targets are far easier to hit at digging and boxing than to fix after the tree is on a truck — and a reduced ball starts a grow-in clock (next panel) that the planting date has to respect.
A smaller ball needs time to grow back
A reduced root ball is not ready to plant the day it is cut. The tree has to regenerate root growth into the smaller ball first — that grow-in time is part of the specification, and it applies to specimen trees and palms alike.
Specimen trees on podiums: a tree prepped with a reduced root ball is held to regenerate root growth before it ships. HessTrees does not ship a podium tree straight from the dig — it goes onto the structure only once the roots have grown back into the reduced ball.
Palms on podiums: the palm is rerooted into a container ahead of the podium placement, so it arrives established rather than freshly cut. A date palm gets at least 90 days of reroot growth before it is placed.
The winter rule: a palm scheduled to go in during the cold window — October 1 through the end of February — must complete its rerooting and be well established before that window opens. Plantings in that window are planned backward from it: the full 90-day re-rooting period must be complete before October 1.
Work the calendar backward from the planting date. If the placement falls in the winter window, the rerooting has to be done before the window — not during it.
06 — Planning Notes
Before you spec, lift, or load
Lifting & handling
Use verified specimen and rigging weights, not the high end of an unverified table, for an engineered lift plan. Check the crane’s rated capacity at the actual working radius and configuration.
Boxes lift from the base / box slings — never by the trunk. Balls lift from the basket / ball slings with the trunk as a tag line only.
The center of gravity depends on the actual specimen and its orientation. A qualified rigger must assess balance, approved lift points, rigging and tag lines; do not assume a standard off-vertical pick.
Transport & access
Widths over 8′ 6″ are a wide load in most states — that means every 10′ and larger ball and every 108″ and larger box — need permits, routing, and often escorts. The 8′ ball and the 72″/84″/96″ boxes are at or under the limit on width, though height and weight permits can still apply.
Check the full route: gate width, overhead clearance with canopy, turning radius for a lowboy, and ground bearing where the crane will set up.
Weights on this page are per tree. A dozen hero specimens for one project is a freight program, not a single load — sequence deliveries to the planting crew.
Basis of this review: square-frustum geometry is checked mathematically; no specimen was weighed. The 18″ taper, soil depths, nursery practices and tree/box allowances come from the original reference. 100 and 66 pcf are illustrative wet-density assumptions, not certified properties. Actual internal dimensions, root-ball geometry, wet density, tree, box and rigging weights must be established for each job. US short tons = pounds ÷ 2,000.
Need the weight for a specific tree?
Specimens are sourced to order and priced individually — signed agreement and deposit in place before any search starts. Send the species, size class, and quantity, and the per-tree weight comes back with the quote.
Round only after calculating. The 16′ × 42″ root plate is 492.602 cu ft, or 493 cu ft to the nearest whole cubic foot.
What still needs measurement
Soil type does not uniquely determine wet density. USDA bulk density is an oven-dry mass divided by whole soil volume; it must not be confused with wet handling density. FHWA examples show that dry and saturated densities vary materially between soils.
The original 84% / 66% soil factors, 0.92 / 1.15 moisture factors and fixed tree/box allowances were not validated. Use measured density or the project’s tested mix specification, especially at saturation.
Original figures and estimator · retained for comparison
Superseded planning figures, not verified limits. These original ranges and settings are preserved so the changes are reviewable. In particular, several original root-ball totals were below the soil-only weight from the page’s own 100 pcf assumption. Use the corrected conditional model above, not these ranges.
Box
Top × Depth
Base (taper)
Soil volume
Est. weight — sandy clay loam
72″
72″ × 72″ × 42″
54″ × 54″
97 cu ft
10,000–12,000 lb
84″
84″ × 84″ × 42″
66″ × 66″
137 cu ft
13,500–16,500 lb
96″
96″ × 96″ × 54″
78″ × 78″
237 cu ft
23,500–28,500 lb
108″
108″ × 108″ × 54″
90″ × 90″
307 cu ft
30,000–36,500 lb
120″
120″ × 120″ × 54″
102″ × 102″
386 cu ft
37,500–46,000 lb
132″
132″ × 132″ × 54″
114″ × 114″
474 cu ft
45,500–56,000 lb
144″
144″ × 144″ × 54″
126″ × 126″
570 cu ft
54,500–67,000 lb
Ball diameter
Radius
Depth
Approx. soil volume
Est. weight
Transport
8′
4′
36″
~106 cu ft
8,000–11,000 lb
Standard flatbed
10′
5′
36″–39″
~179 cu ft
14,000–18,000 lb
Wide load — flatbed, permit req.
12′
6′
39″–42″
~277 cu ft
22,000–28,000 lb
Wide load — lowboy / step-deck
13′
6′ 6″
39″–42″
~325 cu ft
25,000–31,000 lb
Wide load — lowboy
14′
7′
42″
~377 cu ft
28,000–35,000 lb
Wide load
15′
7′ 6″
42″
~433 cu ft
32,000–40,000 lb
Wide load — oversize
16′
8′
42″
~492 cu ft
37,000–46,000 lb
Wide load — oversize
Original estimator · comparison only
The original model is retained for comparison only. Its soil labels, moisture multipliers and fixed allowances were not independently validated. Do not use this legacy model for lifting or structural design.
Estimated total weight25,900 lb
96″ box · sandy clay loam · field moisture · ≈12.9 tons. Soil fraction scales with soil and moisture; tree + box are held constant.
Planning only — confirm by scale before a critical lift or a structural placement.
Recreated from your original Muse reference. Original wording, nursery practices, illustrations and photographs retained where possible. The international shipping section includes two original Hess Tree Company photographs. Numerical review: November 3, 2026.